Long screw in polished alloy dipstick with O ring for models with fairing lowers (dipstick protrudes through fairing to make oil level checking much simpler and more accurate)

Use this longer dipstick for models fitted with a sump extension, note that the dipstick extension is 80mm long which is shorter than the original part. Supplied with both O rings

 This part is available by special order, request a quote

Dimensions:
107mm gasket surface to high mark

Short screw in polished alloy dipstick with O ring for models without a sump extension. Can be used to replace long dipstick and tube on Le Mans 2 and 1000 SP

Will also fit V7 700, V7 Special and 850 GT if high and low levels are transposed from your old dipstick

 This part is due back in stock soon, call 01484 841395 to reserve yours

If you would like to be emailed once this item is available again then click here

17004951-z 17004951 GU17004951 17 00 49 51
 1700 4951 1700.4951 17.00.49.51

Dimensions:
77mm gasket surface to high mark

Polished aluminium blanking plate kit, use when fitting a crankshaft mounted ignition to replace the distributor

Includes O ring and two countersunk screws. See ENA90313 for replacement O ring

 This part is due back in stock soon, call 01484 841395 to reserve yours

If you would like to be emailed once this item is available again then click here

Polished aluminium distributor cover for models with points or electronic ignition. Alternative for plastic cover ENA14420

See SSA05025 for the screws which secure this dizzie cap

 This part is due back in stock soon, call 01484 841395 to reserve yours

If you would like to be emailed once this item is available again then click here

14715420-z 14715420 GU14715420 14 71 54 20
 1471 5420 1471.5420 14.71.54.20

Dimensions:
40mm overall height

Protection bar for bikes rear drive box or bevel box. Protects against expensive damage

 This part is available by special order, request a quote

Cardan guard kit developed to protect both swingarm and drivebox. A lightweight protective guard to protect your final drive from low speed impacts.

Essential protection for your V100 Mandello

 This part is available by special order, request a quote

Hepco 'Easy' luggage rack for V100. Designed for Hepco top boxes it features a pillion grab handle which folds flat when not in use (or when a top box is fitted). The rack is easy to fit and transforms your V100 into a capable touring bike.

No additional adapters needed for standard Hepco top boxes with metal locks. If fitting pannier frames you will need to fit either this rack or LUA02097

 This part is available by special order, request a quote

Special rack for mounting a H & B top box to the V85 TT. Complete with hinged case stop, this Alu-Rack allows you to fit Xplorer and Junior top boxes to your bike using the standard quick release top case fitting

 This part is available by special order, request a quote

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with 12 volt 3 Ohm coils ELA14500 (big twins) and can be used to replace Digiplex on models with Ducati charging systems where the bike is converted to carburettors. This kit is just an ignition system, it will not control fuelling. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Once fitted no further adjustment should be necessary. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. See this link for fitting instructions. Some bikes may need at least one additional spacer to allow enough clearance for alternator cover to fit once pickup is fitted. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA14500

 This part is available by special order, request a quote

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 3 Ohm 12 volt coils and can be used to replace points or Motoplat ignition on models with Saprisa charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA31165

 This part is available by special order, request a quote