Kit of 8 frame and footpeg caps to finish off your V100. The kit, made of plastic material resistant to UV rays and heat, was developed specifically for the Moto Guzzi V100. It consists of 6 footrest caps and 2 frame caps, covering both the right and left sides. The frame caps are finished with a Moto Guzzi eagle emblem in keeping with the branding elsewhere on the V100. These frame caps tidy the side profile of your machine and prevent water and road spray getting into the frame.

Note that the included M10 washer is required to space the gear lever so it is clear of the installed plugs. We recommend using a small dab of glue during installation of the plugs for security. Scan the QR code on the box for a short video guide to installation.

Aluminium spacer which allows the fitting of a round barrel rocker cover (loop or T3 type) on a square barrel engine

You will need two of these for an engine

 This part is available by special order, request a quote

Stainless steel front engine mounting stud kit. Kit contains one long engine M12 x 1.25 threaded stud (with plain section in centre), two M12 half nuts, two M12 crinkle washers and four standard M12 washers - all in A2 stainless steel

The original bolts are prone to seizing in place so we recommend replacing with this quality stainless part. Also known as Guzzi ref. 03429500, 14429505
Differs from original part whcih is a bolt, this stud make is easier to fine tune the position of the stud between header pipes

 This part is due back in stock soon, call 01484 841395 to reserve yours

If you would like to be emailed once this item is available again then click here

 14429500 GU14429500 14 42 95 00
 1442 9500 1442.9500 14.42.95.00

Lightweight aluminium M20 gearbox and drive box filler plug (big twins), drive box level plug (small twins).

 This part is available by special order, request a quote

 12022600 GU12022600 12 02 26 00
 1202 2600 1202.2600 12.02.26.00

Dimensions:
M20 x 1.5

Budget chrome bar end mirror with a large round head and adjustable arm. Fits all models with open ended (i.e. not threaded) 7/8 inch steel handlebars.

Can be fitted on either left or right hand side of handlebars. Shown here fitted to a handlebar which is not included

Dimensions:
125mm diameter head

Kit containing 1 pannier latch lock and clasp, key and 2 hinges (all chromed) for original type panniers

 This part is due back in stock soon, call 01484 841395 to reserve yours

If you would like to be emailed once this item is available again then click here

Kit containing 6 titanium shouldered retaining screws for rocker cover. Upgrade your corrosion prone zinc OE parts with a polished upgrade. Note that one bolt on each cover is hidden under a plastic cover, if you would prefer to only buy four bolts then see SSA84291

Rocker cover bolt kit. We recommend that you check length of bolts on your engine before ordering as two lengths of bolt were used. Supercedes Guzzi ref. 976591
See ENA83249 for rubber sealing washer

 842291 MG842291

Dimensions:
M6 x 13mm

Gorgeous polished aluminium reservoir cap for PS15 Brembo master cylinder fitted to rear linked system on many models, will fit front master cylinder on models where a PS15 handlebar master cylinder is fitted. Seal is not included with this cap - you should re-use your original cap seal

Make your Guzzi stand out from the crowd!

 This part is available by special order, request a quote

 14661100 GU14661100 14 66 11 00
 1466 1100 1466.1100 14.66.11.00

Also fits Ducati 600 SL Pantah, Ducati 750/900 SS, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR, Ducati 1000 MHR

Gorgeous polished aluminium reservoir cap for PS12 Brembo master cylinder fitted to front brake on many models, fits rear master cylinder on more recent models

Make your Guzzi stand out from the crowd!

 This part is available by special order, request a quote

 10430830 GU10430830 10 43 08 30
 1043 0830 1043.0830 10.43.08.30

Dimensions:
53mm OD

Replacement seal to fix your leaking factory pannier

One seal required per pannier. Not for aluminium luggage.

 Sorry, this part is no longer available.

 883246 MG883246

Dimensions:
1600mm length 27mm width