Chromed M20 swing arm pivot stub lock nut

See FRA93180 for nut rubber

 14547800 GU14547800 14 54 78 00
 1454 7800 1454.7800 14.54.78.00

Also fits Benelli 900 Sei

Dimensions:
30mm across flats x 11mm thickness

Taper needle roller bearing used as steering head bearing

2 sets required per bike. Also used as rear drive box pinion bearing on big twins with rear drum brake

 92249225 GU92249225 92 24 92 25
 9224 9225 9224.9225 92.24.92.25

Ball bearing used for gearbox output shaft output end on small block twins

Mainshaft front on V50 II & 3, layshaft rear on V50, V65, V75. Used for rear wheel bearing on 850T (2 bearings required)

92201220-z 92201220 GU92201220 92 20 12 20
 9220 1220 9220.1220 92.20.12.20

Dimensions:
47mm OD

Ball bearing, used for front wheel on loop frame models with 4 shoe front drum

2 required for front wheel. Also known as Guzzi ref. 92201421

92201420-z 92201420 GU92201420 92 20 14 20
 9220 1420 9220.1420 92.20.14.20

Dimensions:
52mm OD

Full service kit for pre PI engine EV models containing 1 x UFI or Mahle oil filter, 1 x UFI air filter, 2 x NGK BPR6ES spark plugs, 1 x sump gasket, 2 x rocker cover gaskets, O ring and all crush washers to complete a service on your bike

Save £'s by buying everything in a service kit

See FUA29106 for fuel filter, ENA95006 for gauze oil filter tab washer. Oils and lubricants available separately. The oils you need are 1 x OIA01152 and 1 x OIA08194 or save time and money by ordering service oil kit OIA18004 with your service kit.

Full drive box seal kit and gasket set for overhauling the rear drive box

For Breva 750 from frame no. LL111908.

Bearings available separately

14 sided UFI 23 287 00 cartridge oil filter with sealing rubber. This one item is new old stock and does have some marks to show this.

From late 2015 onwards 1200 models used SIA06428

See SIA15301 for alternative filter from Mahle. Please note that Daytona 1000 models where filter screws into base of sump require SIA14530. This is a 14 sided oil filter. Use tool TOA41005 if your filter is located inside the sump, use tool TOA01200 if you change your oil filter without removing the sump

 30153000 GU30153000 30 15 30 00
 3015 3000 3015.3000 30.15.30.00

Dimensions:
90mm x 75mm diameter overall, for 19mm OD spigot

Full seal kit and gasket set for overhauling the rear drive box

Bearings available separately

Exhaust stud kit consisting of 4 x titanium studs, 4 x stainless dome head nuts and 4 x stainless wavy washers

The mild steel exhaust studs fitted to modern Guzzis are notorious for corroding in place. Replace yours now with these corrosion resistant parts to ensure you can remove your exhaust in years to come

1A003632R

Dimensions:
M8 x 48mm studs

Kit containing 2 Litres of Millers ZFS 4T SAE10W-60 synthetic engine oil and 1 litre of 75W-140 gearbox and final drive oil. This kit contains all the oil you will need to change your engine, gearbox and drive box oil.

Please note this kit CANNOT be posted outside of the UK mainland area