Clever stand which makes working on your bike much easier! This stand clamps safely to the bolts just underneath the rider footrests, and allows you to lift the bike securely in a similar action to a centrestand.

Useful substitute for a centre stand.

Needs 2 x 18mm 0.5 inch drive sockets to fit a V11 (not supplied)

 This part is available by special order, request a quote

 979717 MG979717

Clever stand which makes working on your bike much easier!

Useful substitute for a centre stand from Becker.

 Availability varies on this part, call us to check availability

If you would like to be emailed once this item is available again then click here

Brembo PS 13 handlebar mounted clutch master cylinder, supplied complete with lever.

 This part is available by special order, request a quote

Pair of adjustable Tommaselli clipons, quality aluminium castings and chrome plated tube

38mm rise, these clip ons pivot on the central bolt to adjust the handlebar angle, pull back angle is adjusted on the fork stanchion clamp. These clip ons are unsuitable for use with the PS12 handlebar master cylinder fitted to small twins unless the master cylinder is modified. Bar ends are held in by a rivet and some modification will be needed if you wish to fit bar end mirrors.

 This part is available by special order, request a quote

Dimensions:
For 32mm stanchions, 223mm usable handlebar

Pair of triangular side panels with fixings to fit all Tonti frame models with slotted side panel lugs under the seat

This is a kit, the fixings need bending and glueing to the sidepanel before the side panels can be fitted. The panels are GRP, fitting instructions are provided in German

 This part is available by special order, request a quote

Aluminium spacer which allows the fitting of a round barrel rocker cover (loop or T3 type) on a square barrel engine

You will need two of these for an engine

 This part is available by special order, request a quote

Short screw in polished alloy thermometer dipstick with O ring for models without a sump extension. Shows oil temperature in degrees celcius

Supplied unmarked, you will need to mark the rod using a small file to match your existing dipstick

 This part is available by special order, request a quote

17004951-z 17004951 GU17004951 17 00 49 51
 1700 4951 1700.4951 17.00.49.51

Dimensions:
121mm from end to sealing o ring

The Power Commander is a fuel injection and ignition timing (on some models) adjustment unit that plugs "inline" with the bikes' stock ECU. The Power Commander uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes, some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the Power Commander's onboard microprocessor. Using this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes' ECU (electronic control unit). Removing the Power Commander returns the bike to its previous stock condition. The Power Commander can be ordered preprogrammed with a your choice of several settings, based on the modifications to your bike. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.

This is for V7 models with twin throttle bodies, it is not compatible with single throttle body models

 This part is available by special order, request a quote

The Power Commander is a fuel injection and ignition timing (on some models) adjustment unit that plugs "inline" with the bikes' stock ECU. The Power Commander uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes, some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the Power Commander's onboard microprocessor. Using this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes' ECU (electronic control unit). Removing the Power Commander returns the bike to its previous stock condition. The Power Commander can be ordered preprogrammed with a your choice of several settings, based on the modifications to your bike. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.

 This part is available by special order, request a quote

The Power Commander is a fuel injection and ignition timing (on some models) adjustment unit that plugs "inline" with the bikes' stock ECU. The Power Commander uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes, some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the Power Commander's onboard microprocessor. Using this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes' ECU (electronic control unit). Removing the Power Commander returns the bike to its previous stock condition. The Power Commander can be ordered preprogrammed with a your choice of several settings, based on the modifications to your bike. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.

For 4 valve models

 This part is available by special order, request a quote