Tubular luggage rack finished in chrome.

Silver finish front engine guard to protect the front cover of you V100 from stone cips and corrosive road grime. Fit now before damage occurs

This engine cover manufactured is from AW5083 aluminium for toughness. Fit in conjunction with a EXTRA Fenda Extenda ACA58780 for maximum protection.

Kit of 8 frame and footpeg caps to finish off your V100. The kit, made of plastic material resistant to UV rays and heat, was developed specifically for the Moto Guzzi V100. It consists of 6 footrest caps and 2 frame caps, covering both the right and left sides. The frame caps are finished with a Moto Guzzi eagle emblem in keeping with the branding elsewhere on the V100. These frame caps tidy the side profile of your machine and prevent water and road spray getting into the frame.

Note that the included M10 washer is required to space the gear lever so it is clear of the installed plugs. We recommend using a small dab of glue during installation of the plugs for security. Scan the QR code on the box for a short video guide to installation.

HIgh performance aluminium velocity stack for airbox to throttle body union. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM

This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434

Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.

Black plastic front mudguard extension or Fenda Extenda. This will protect the exhaust pipes and front engine cover on your Guzzi from road debris, salt, water and traffic grime thrown up by your front wheel

Specifically designed to follow the contour of your bike's front guard, our Extenda Fenda is supplied with both plastic rivets for mechanical fitment and a sheet of our specially sourced 'Stick Fit Pads' for those customers who would prefer not to drill their front mudguard. Our Extenda Fenda is simple to install and will arrive safely packaged, together with comprehensive fitting instructions and all necessary fittings as detailed above. See this video for help fitting yours

Pair of standard KYB factory rear shocks with black springs

Low mileage OE part with preload adjustment

Sorry this part cannot be shipped to the US or Canada

6 month warranty on this part

 1 in stock

2B006790

Dimensions:
370mm x 12mm bushes

High performance aluminium velocity stack for airbox to throttle body union on single throttle body models. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM

This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434

Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.

Engine guard kit developed to protect both header pipes and cylinder head. A set of lightweight ice grey finish aluminium head guards for your V100. These include a shock-absorbing pad to protect the head, rocker covers and exhaust headers from low speed impacts.

Lower profile than a conventional crashbar these are an essential piece of kit for your V100 which will help protect expensive engine and exhaust components in the unfortunate event of a low speed spill. Tested by Mistral.

Fit yours before you need them!

See this video for installation instructions. Note that black protectors are shown in second photo.

The Mistral footrest kit offers a much improved foot position for the pillion by lowering the footrest to immediately above the silencer. By extending the leg position, pillion passengers feel more secure and touring comfort is much improved. This reasonably priced Mistral footrest kit is made close to the Guzzi factory in Mandello and looks as good as any stock part. Fitting is simple using the original attachments (springs, bolts, etc.).

Black painted finish. Compatible with both Mistral and stock silencers. Kit contains components to lower both pillion footrests and includes shims to remove excess movement. See this video for installation instructions.

Pair of black tubular rocker cover protector bars for round and square barrel engines, these will protect barrels and rocker cover in the unfortunate event of your bike being dropped

These head protectors bolt to the head using existing rocker cover bolts, they won't fit models with fairing lowers that wrap around the cylinders (e.g. Spada) without modification. To modify simply reduce the length of the rear section of the bar to stop short of the fairing and insert the supplied grommet. These bars are supplied with a plastic grommet for each end, this will need chamfering or leaving off on round head models with bolt on rocker cover breather pipes, e.g. T3. These bars will not fit on a T3 or other model with knee pads

 This part is due back in stock soon, call 01484 841395 to reserve yours

If you would like to be emailed once this item is available again then click here